5VET2WPKLQ00 Whirlpool Refrigerator - Instructions

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Remove 4 screws to remove old handle. Install new handle

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Very easy to do. Crisper frame just snapped in and fit well.Very happy with results.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Cut support and replaced. Easy

Ordered new set and installed

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I simply took the glass cover from the package. It came packaged really well. Thank You so much for that! I was concerned about breakage. Once it was released for packaging, I simply slipped it into place in the refrigerator. It was very easy.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

All I had to do was snap the end caps into the shelf holder and snap into the door. Easy as can be!