1VET27DKXGW0 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Oakland Park, FL
- Parts Used:
- R0151005
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
My evaporator fan motor quit working
This was an easy repair just simply removed a handful of screws to remove the back and top panels making the fan motor accessible. The whole job took about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard J from Derby, CT
- Parts Used:
- D7714408
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light socked cracked.
Turn off power. Remove 1 screw to remove the plastic cover (cover snaps out). Snap out socket. Pull off two wires. Plug wires onto new socket. Snap in the socket. Replace the cover and screw. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Laramie, WY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Mountain View, AR
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Ice Maker Quit Working
Replaced valve on back of freezer and replaced the ice maker tray. Took about 20 minutes and had new ice cubes 1/2 hour later. It's working like it did when it was new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from NANTUCKET, MA
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No Ice
Reversed the order of taking it out. . . Put it back the same way. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from holly, CO
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no water coming in
Replaced the fill valve on the back of refrigerator took about 15 min. We had that night
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Columbiaville, MI
- Parts Used:
- W11177593
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer seal was broken
Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from north wildwood, NJ
- Parts Used:
- 4396418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
water was running into the bin and making a big chunk of ice in addition to the cubes
removed the old unit and put in the the new one, no other parts were needed
Was this instruction helpful to you?
Thank you for voting!