EB22DKXFN01 Whirlpool Refrigerator - Instructions

I took the cover off of the evaperator in the back of the freezer compartment and thawed the ice out with a heat gun. I then replaced the bimetal defrost timer I did have to change one connection as it would not plug into the harness.
I found the Defrost timer in the front of the refrigerator behind the filter cover at the bottom. Just one screw and a quick plug in and everything is working wonderfully. no more icing up

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

first I took the inside freezer panel off. Pulled off the deformed gasket. I noted how it was attached to the door. I then took the new gasket and placed it on the panel and reattached the panel to the freezer door. The screws are small and can get easily misplaced. Use a recepticle to hold the screws, it does make the job much easier. I also used a power drill which made the job move along nicely. Easy as pie. Thanks. I know where to get my parts in the future.

Most difficult part was finding where they hid the defrost timer. (it is in the left front under the fridge behind the kick panel.) just unscrew the two fastener screws from the front, tilt fridge up on one side, slide timer bracket back and remove. Unplug and remove timer from metal bracket. Replace timer and remount bracket.

Followed the video instruction and it was fairly easy to install. Let the gaskets sit for a day to reshape itself. Started by loosening the screws then removal of the gasket was done. The only hard part was to align the Gasket evenly. Not removing the doors made the install a little more difficult for alignment.

Emptied unit and removed screws holding panels at rear of freezer compartment. Removed panels. Removed two screws holding motor. Made diagram of wire locations and fan blade orientation. Removed three wires and fan blade from motor. Took new motor and installed wires and fan blade to motor. Installed motor with screws. Test ran frig and reinstalled panels.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

Removed panel and motor cover at rear of freezer compartment. This requires 1/4" nut driver. Removed motor assembly bracket and wiring, careful to note where ground, neutral and hot were attached. The entire assembly must be removed from the freezer compartment in order to swap new motor for old motor. Re-inserted assembly into freezer compartment, reattached wiring. Made sure all assembly screws were tightly fastened and wiring was correct. Re-attached panel cover and motor cover. I did note that a few of the 1/4" machine screws wobbled in the original holes; I used slightly larger, 5/16" head machine screws of identical length as replacements. New motor is much quieter. No longer sounds like a truck is idling in our home.

I left the new seal out in the sun to warm up, while it was warming up I took the door off of the fridge and laid it flat. I removed all of screws holding the plastic shelves in place, removed the old gasget fitted the new one and reinstalled the door.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!

First I removed the cover to the evaporator in the freezer section and found the coil iced up, then I turned the defrost timer until it clicked into the defrost mode, the heaters came on so I left the timer in the defrost mode to defrost the coil, it stayed on and did not change. The timer motor was bad, I ordered a new part and had to manually defrost the refrigerator by turning the timer. To replace the part I had to first unplug the power cord then pull the kick plate off at the front of the refrigerator and remove two screws that hold the timer in place, then pull it out unplug the electric plug in the new timer secure it with the two screws and put the kick plate back in place. I then plugged in the power cord and the refrigerator came on as is now working great..