ED19HKXRCR0 Whirlpool Refrigerator - Instructions

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks

I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old

Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)

By watching a video.

I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus shipping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00

Unscrewed old broken part from the kickplate and attempted to install the new clip. Mounting screws would not go into the new clip. Had to drill out the mounting holes in the plastic clip using a #30 drill bit. Once the new clip was mounted, attempted to snap the kickplate back in place. Unfortunately at the left side the kickplate would not fully mate with the metal clip on the refrigerator body and would not snap all the way back to the refrigerator front surface, as the right side does. At least the kickplate doesn't fall down onto the floor on the left side as it did before. I suspect there is an alignment problem with the left side refrigerator metal clip, but have not pursued that yet.

First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

We dealt with this problem for well over six months. Last week while visiting our home my mother tried to schedule a repair man to come out. Upon hearing this conversation i urged her to hang up the phone and let me fix it. This prompted me to go on line and find the three dollar part needed to fix it. With the help of a friend to lift and hold the door i unbolted the black closer piece and replaced it with the new one. This whole process took less than 10 minutes and completely fixed the problem. The service visit would have cost upwards of $80.00 so this was well worth the two days shipping i paid for.

took door of and replaced ,no problem

I followed the video that you have for this part and it was very easy to repair. The video that you put together showing how to do the repair, made the job very simple, and your service was outstanding. What a great web site!!! Thanks