ET0MSRXTD00 Whirlpool Refrigerator - Instructions

I did the repair just as your video showed me. It worked out great.

1. I removed the plastic back cover panel in the freezer. 2. Took flash photos with my phone of the motor and wire configuration. 3. Removed noisy Evaporator fan bracket from freezer. 4. Removed Fan Blade from old Motor. 5. Removed old Motor from Bracket. 6. Installed New Motor into the bracket. 7. Installed the fan blade onto motor spindle. 8. Installed the bracket onto the back wall of freezer. 9. Noticed that the tab for the ground wire was inaccessible. 10. Cursed like Linda Blair in the Exorcist for about 5 minutes. 11. Repeated steps 3 - 5... 12. Unscrewed the ground tab and placed it on the opposite side and screwed it back in. 13. Repeated steps 6 & 7.... 14. Tried to install the bracket and motor back onto the freezer but the bracket screw holes weren't lining up. When I removed the motor to flip the ground tab over, I reinstalled the motor onto the bracket upside down. 15. Tear some hair out of my head. 16. Repeated steps 4 & 5 and flipped bracket over. 17. Repeated steps 6 - 8... 18. Placed wires onto tabs. 19. Ground wire would not stay securely onto the tab. 20. Slightly opened up metal fastener of ground wire with needle nose pliers and stuck it onto the tab. 21. Still not on there super tight. I gave up wrestling with it and just prayed it will stay on there anyway. 23. Turned on freezer to check if it works. 24. Reinstalled plastic back plate. 25. Put melted food back into freezer.

I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

I ordered the crisper pan by the model number and received it the very next day!! All I had to do was slide the old broken one out and slide the new one in, and voila! It was as easy as fitting cinderella's slipper(on her feet of course).

Used angle screwdriver to tighten.

Replacement was very easy. Pulled the broken drawer and slid the new one in. Less than 2 minutes. . . . . . The only problem I had was the original part I ordered was broken in shipment. I called partselect and they were very helpful. They gave me a refund and had a new one shipped the same day and I received it in less than 2 days. I don't think I have ever had that good of service from anyone I have ever done business with. . . . . . John l. H. C. Arizona

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.

I just followed the enclosed instructions

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.