GB22DKXGN01 Whirlpool Refrigerator - Instructions

Removed the lower door, 4 screws, lay on flat surface. Working gently pull the seal back to get to the screws holding the seal. Save the screws to put the new seal back on.You may need someone to help hold the door when remounting it.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

hook on end of clip on back of grill. With that end firmly in place a screw driver on the other end of clip (inside ) & bump with your hand. total install time 60 seconds

I slid the bar into the end caps, then slid the end caps into the slots on the door. No tools were required. My fridge is old, and I was very pleased that I was able to find the part.

Took the ice maker out with three screws hving turned water off and unplugging fridge. Put a new one back in with the three screws. plugged fridge back in and turned water on. All done and everthing worked fine.

Ronald Stonis

Once I removed the contents of the freezer I found ice on the inside back panel Removing the panel I found ice on the cooling coils and the defrost thermostat was bulged out where the wires were attached.I removed the panel with the nutdriver as shown in the video. I removed the ice maker connection and removed the panel from the freezer section. I then had to manually defrost the area with a heat gun. The ice had actually covered the Defrost Thermostat - which was bulging where the wires were attached.. The defrosting took the majority of the repair time - the actual Defrost Thermostat replacement only took about 20 minutes once I could get to it. I spliced the wire with a crimping tool as discussed in the video. Once all was defrosted I reversed the operation.Overall, a very simple part change out. The video was extremely helpful - if nothing else to mentally prepare me for the task.

Talked to a bud who does this kind of work and he walked me thru the simple job. Also watched a you tube segment. Very easy job. Took off the front kick vent panel. Unscrewed the metal holder and unplugged old part, plugged new part in and put panel back on. Turned on unit and it is working like a charm. Got my fingers crossed just in case.

I removed the back cover in the freezer section by removing six screws. The entire coil, the thermostat and the lines were all iced over. I used a hairdryer to defrost everything. I removed the thermostat by uncoupling the connectors and unclipping it from the coil tubing. I found the thermostat was bulging and deformed. I jumped out the thermostat using an insulated clip lead. I taped it so it would not short to anything. I plugged the unit in, turned the unit to "1" and advanced the defrost timer to defrost. I could hear the water hissing on the coil. I ordered the thermostat. It arrived in 3 days. The new one had a different terminal. I cut off the matching one from the old part and used a scotch-lok to make the connection to the new part. I slapped it in, dressed the wires and replaced the cover. I noticed that when I advanced the timer after replacing the thermostat, it did not immediately come on. The thermostat has an operating temperature window. I checked it several days later and found no frost. Everything works great.

snapped the new ones on the aluminum bar and inserted into the freezer

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Needed ice maker bucket for extra fridge. Part came the next day, and worked perfectly.

I took out the old one and put in the new one. For some reason the repair story associated with the ice bucket had nothing to do with ice buckets.

Water Intake valve for icemaker in Amana refrigerator
We found that the icemaker was not getting water due to a faulty intake valve. The original valve had a plastic coupling on the vinyl tube leaving the valve. The replacement valve had a quick connect coupling. Replacing the valve with the new part gave a significant leak. After discussion and viewing YouTube directions multiple times, the part was returned; and a new part was sent. It also leaked.
After searching, a video was found that dealt with the no-fail quick connect. The problem was not in the quick connect but in the tube from our refrigerator which had a spring inside the last five inches of the tube. This aided the prevention of a leak when the original plastic coupling had been installed.
SOLUTION: Removing the part of the tube with the spring using a clean cut allowed the quick connect to work preventing the leak. This needs to be mentioned in the how-to videos to save others having a problem. Also, these instructions with the part would be helpful.

The longer than usual repair times shown above were the result of the spring insert in the plastic water tube of the refrigerator. Nowhere in the how-to instructions were references made of either an insert in the tube or quick connect procedures.

We were well pleased with the support rendered by the PartSelect staff.

My husband and I worked on it for hours, until we gave up and put the whole project off for the next day. The next day was not fruitful either, so we called my brother, who has had experience with this sort of thing. He figured out that the screws all around the door needed to be taken out. Finally, relief!! If there had been instructions included with it it would have been a snap. Long story, but a lot longer than it needed to be. (Of course, I could have looked online for instructions!) As for the product, I give it an A+. But the clamp is still holding the door closed. It was so stretched out on one side from our efforts that the door would not close. Well, you did say, "Describe how you did the repair".

I used the process of elimination. The freezer was cold but the fridge side was warm. The motor was runing but the fan was not working. I unplugged the power cord and pulled everything out of the freezer. Then I took the coil cover out. The unit was frozen solid. I used my wifes hair dryer to melt the ice on the coil and spray water with a bottle to speed up the process. It took about 15 minutes to melt the ice and plug the power cord again. The motor kicked on and the fan started blowing right away so I know it's not the fan. The following morning it was frozen again. I repeated the process of taking everything out and tested the heater element with a multimeter. It wasn't working allowing the ice to build over the coil so I replaced it. It took about 30 minutes to replace but two days later it froze again. I read a little to learn about the timer and the thermostat function in a refrigerator. The timer rotates to turn off the motor and turn on the heater element to melt the ice on the coil. I tried to rotate it but it felt too hard to turn and it smelled burnt out so I replaced it at once. It took me less than 10 minutes to replace. I also learn that the thermostat reaches certain temperature and activates the fan which blows the cold air out of the coil and throughout the fridge compartments. Because the coil and the thermostat were getting covered in ice, it was not activating the fan to blow the air out keeping the freezer side cold and the fridge side warm. By replacing them both, the thermostat and the timer I solved the problem. It took about 30 minutes to replace the thermostat but now it's working like a brand new one again.