4YED20TKDN00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elyse from Skokie, IL
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the light socket broke apart
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ENDWELL, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from patterson, CA
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
light on inside, fridge and freezer warm up after initially cooling
Fridge/freezer warm. After unpluging and plug in again, both would get cold. Then, ice would partially melt in the freezer only to refreeze later. Noted large temperature swings in freezer-up to 48 degrees during defrost cycle. Finally after a day or two, both sides warming up permanently to room temp. Tapping inside the fridge near the cold control (thermostat) would cause the warm fridge/freezer to cool again. Installation is simple. Remove knobs and snap on face plate in front top of fridge. Remove screws allowing plastic cover to drop down which houses the thermostat at the inside top of fridge. loosen two mounting hex head screws from thermostat mount. Remove two plastic covers concealing thermostat wire that travels to vent at back of fridge. Remove thermostat. remove plastic tube over wire on old thermostat by slipping it forward and slide tube on to new thermostat wire. Install is the same in reverse. A thermometer in the freezer confirms very little temperature variation after install (3-4degrees); ice no longer melts, unit stays on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Conyers, GA
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door on a side by side unit would not stay closed.
First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Was this instruction helpful to you?
Thank you for voting!
3 shelf retainers in freezer broke off over time
snapped the new shelf retainer end caps onto one new trim-door and 2 old ones and snapped all 3 back onto the freezer door above each shelf so I can now use 3 freezer shelves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Amherst, MA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Lower hinge on freezer door on side-by-side broke
Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line which we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from JACKSONVILLE, FL
- Parts Used:
- WP2188661
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked refrigerator drawer (crisper pan)
It took me about 15 seconds and could not have been easier. I opened the box, pulled out the new drawer, opened the refrigerator, pulled out the cracked drawer, and inserted the new drawer. Done. I can't believe I waited so long to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from LEHIGHTON, PA
- Parts Used:
- 4388538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken shelf support stud
Just followed the video supplied with shipment. 5 minutes, even for a mechanically-challenged person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from BAKERSFIELD, CA
- Parts Used:
- WP2188661
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer was damaged and would not pull out or push in.
Replaced the drawer with a new replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAUGERTIES, NY
- Parts Used:
- W10864399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper shelf glass missing
Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Green Valley, AZ
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old part cracked and broke
easy - remove the door, replace th part, put back the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from SPARKS, NV
- Parts Used:
- WP2188661
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper bin had broken pieces off the track edges
Bought new one and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valaida from FRANKLIN, VA
- Parts Used:
- WP2188661
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked
Else one out and the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from MT JULIET, TN
- Parts Used:
- WP2188661
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken chrisper pan
Slid the broken one out and slid the new one in.
Was this instruction helpful to you?
Thank you for voting!