5VET6WPKLQ04 Whirlpool Refrigerator - Instructions

Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plugged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM

Used angle screwdriver to tighten.

Had no problem at all it took about 5 minutes to get the tray off and about 5 minutes to put new tray on.New part fit perfect. Thanks Robert Lovern

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Removed themostat cover with screw driver, unpluged thermostat, pluged in new thermostat, reinstalled cover. Thats it, very easy.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch