GC5NHAXVY00 Whirlpool Refrigerator - Instructions

The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks

First I removed the tracks from each side of the metal rack. Very easy using your hands to slide the tab until the part falls away.

Next I inserted the track into the tab position and snapped it into place.

Warning, dont let your kids pull the produce bin out all the way to the end of the track as it will bend and then finally crack like mine did, but thankfully an easy fix using the PartsSelect.com web site with their easy to navigate parts illustration list and manual.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Replacing this part was a breeze. But I could not believe how fast the part arrived at my doorstep - was expecting it to arrive in 3 days but it arrived in 2. And the part exactly the right one - the pictures on the sight helped a great deal in correctly identifying it.

I would absolutely order from here again and recommend it to friends.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Replacing my old ice maker with the new ice maker that I bought through PartsSelect was fairly easy. The part came without any directions - so I am glad that I did a little research on PartSelect prior to ordering. I am not the most mechanically coordinated person - but even with my large hands pulling the old ice maker out and putting the new one in was simple.
Only real problem was trying to snap the plug in and making sure that the connection was completely tight. With a side-by-side refrigerator - getting my hands and shoulders (I am a large man) far enough in to apply enough pressure to snap the connectors was a challenge.
Within 30 minutes, my wife heard the ice maker making ice - I was a hero and I had saved about $150 in the labor I was quoted.

On this model, access is very easy. The tray slides forward, and then lifting up with a little force at the back of it clears a stop, allowing it to slide out. This exposes two Philips/sq2 screws that hold the faceplate in place. The faceplate swings out and is lifted off the top edge. Disconnect the wire harness and set aside. Trace the cable from the door motor to the control board. Disconnect the cable and fish up behind the facing material. Remove screws holding the dispenser door mechanism. On that assembly, remove the screws holding the motor to the mechanism. Replace the motor. Put the mechanism back in place engaging the metal actuator arm in the door. Fish the cable down to the control board and plug in. Plug the faceplate wiring harness back in, and reinstall the faceplate. Secure with two screws and replace the tray. Done.

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Simply cut the water tube on both sides of connector and push in the new one.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

I replaced this same ice maker a month before, if that long, using a part I found $40 cheaper from another site. Needless to say you get what you pay for, the existing part was not exactly the same as the original and leaked water all over the place. I removed the not so old icemaker by removing the flapper door and removing the harness cover then pulling out the existing icemaker followed by disconnecting the wiring harness. Now with the old icemaker removed I removed the bottom tray/shield from the existing ice maker by removing the three screws from it then attached the tray to the bottom of the new ice maker from PartSelect which did not come with the bottom tray/shield. Finally, I executed the removal process in reverse order to install the new ice maker.