3ET16NKXDG00 Whirlpool Refrigerator - Instructions

lift glass from shelf. Insert back end of bracket first and snap the front in place. Install both drawers and replace glass and insert both drawers

Viewed the viedo - it showed what to do

just poped it in

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Dear Part Select...What a wonderful easy experience....typed in model number...ordered part....it was affordable and arrived in 12 hours....snapped it in...booom.....finished....thaank-you!!!!!

Cut support and replaced. Easy

Replacement rail slipped into to the refrigerator in seconds! The best part of this story is the Excellence of customer service!!! After a long fruitless search for the replacement part, I found the website, ordered the part that I thought was appropriate. When I received it, i realized that it was too short. I phoned customer service, explained the situation and after giving the representative the make and model of my refrigerator, she promptly located the correct part and e-mailed instructions for return of the other part. I had spoken with the representative around noon on Wednesday and when I arrived home Thursday evening, the replacement part was already at my home!!!! I heartily commend this supplier. I had spoken to a representative when I first ordered the part. He straightened out a shipping address issue and was super! The second person that I spoke to was gracious and so efficient! I highly recommend this site!!!

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

put the replacement part in..........pretty simple.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I removed the screws on top of the refrigerator and the freezer door, lifted the fresh food door off bottom hinge laid it on a covered floor, used a pair of wire cutters to cut old gasket. then pulled the gasket straight out all the way around. then I started on one corner using a putty knife to push the new gasket under plastic trim, then put gasket on opposite corner at top of door then did the same with other two corners, then used putty knife to go all the way around sliding gasket under trim. was easy.

I was able to replace the the shelf bars with no difficulty after finding the right parts on PartSelect. The easy to view measuring menu helped me get the right size for the fit I needed. You always worry when you don't have the item in front of you but they make it easy to gauge. I will use them again. I replaced three bars that had been driving me crazy.