WRFF5333PZ03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willie from LOUISBURG, NC
- Parts Used:
- W10830162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad door gasket
pull out old gasket and pushed in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE from WEST PALM BCH, FL
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had no problem
Just take the crisper out and just put it in the hall access
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WATERVILLE, MN
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Clean the glass and asked my wife to install the glass. She is less likely to brake the glass
Removed the plastic frame, washed the frame and fridge, set new glass into the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenny from Boca Raton, FL
- Parts Used:
- WPW10350564
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer Cold at 2 Degrees, Refrigerator Warm at 48 Degrees
Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Southbury, CT
- Parts Used:
- WPW10317076
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lightening storm damage mother board
Appliance Tech did the install. He did have an issue getting the cover off where the mother board was. But finally succeeded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from JOLIET, IL
- Parts Used:
- WP67002633, WP67001716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
BOTH THE LADDER HOOKS, AND THE CRISPER PARTS WERE BROKEN
SIMPLY REPLACED THEM
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from CORSICANA, TX
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator light stopped working
Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from LK HAVASU CTY, AZ
- Parts Used:
- WPW10235370
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The glide for the panty door broke and a new one was ordered.
The glide was very easy to put on; however it is easiest to put in the front screw first, due to the thickness of the glide. Pretty easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
Stopped making ice
Initially I thought it was the valve that provides water to the ice maker. Days prior to go bad, it was making intermittent noises while filling the ice maker. I couldn't tell if it was the ice maker or not. It doesn't have a way to test it or reset button. So I decided and bought both parts, the valve and the ice maker unit. The installation was pretty straight forward. It takes ~30 minutes to replace. The ice maker ended up being the defective part. The one I got is a little bit different because it have a ON/OFF switch while the original did not. But everything else was exactly the same. Regarding the valve, it was good, so now I have a spare one in case it fails in the future. I'm glad I found this website to get the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from McKinney, TX
- Parts Used:
- W10619951
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Water pooling on the floor.
This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!
Was this instruction helpful to you?
Thank you for voting!