3VET19GMFW00 Whirlpool Refrigerator - Instructions

Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then rerouted it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.

Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top screws. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.

Very simple fix, remove 3 screws, two connectors to the old switch

Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small level and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemaker and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!

The rail just snapped into place with a light pressure. I worried it would require manipulation or heavy pressure and I would break the end while installing it.

First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.

Attached new ice maker in reverse order.

Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.

Using a screwdriver

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.

The bent hinge caused a bad seal which let in air into the freezer, so there was a ton of frost build up. I ordered the parts, and they came in 2 days! I figured what tools I needed, got my wife to help hold things, and in 20 minutes it was like new.