WRS331SDHW07 Whirlpool Refrigerator - Instructions

I was unable because you do not even carry the par that you still advertised on you sit and I was charged $20.00 to return the par. The representative was very rude and accused me of ordering the incorrect part as if I don't know the difference between a hose and a filter. When i expressed the poor customer service he disconnected the call. I will never patronize your business or recommend it to anyone.

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

took the old one out and put the new one in. Done

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

removed old and replaced new. Did not need the holder.

Removed the old ice maker by taking out three screws. Unplugged the electrical connection to the old ice maker. Replaced the old ice maker with the new one. Reconnected the electrical, replaced the screws, and reset the new ice maker. The replacement part has been working perfectly. This was an extremely easy replacement job!

This is a very basic model refrigerator and the only model we could purchase when our machine failed suddenly. The new unit works just fine, but we really missed the snack storage of the higher level units. I ordered the parts for the next higher model Whirlpool side by side refrigerator and installed them without incident. They new snack drawer is a little difficult to snap into place, but it fits perfectly and we certainly appreciated the extra snack drawer on our basic model.