WRMF3636RB00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wendy from Shakopee, MN
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The kickplate tabs broke off
It was very easy I just push ito n and it snaped right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie E. from Elk Grove, CA
- Parts Used:
- W11028221
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
rust on the shaft in bottom drawer freezer
Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Palatine, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I broke the switch pulling the freezer basket out.
I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard A. from Boones Mill, VA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Milk was freezing in Refig section, 28 F temp
Noted the Damper Assemby in the upper rear of refrig section,was always staying open during checks for problems. Controls appeared to be controlling temp changes when adjusted. Pulled the damper assemby after removing two screws holding the diffuser/cover(diffuser pops off with screwdriver) Damper assembly snaps out , unplug wires, snap new damper assembly in place, reconnect wires at the plug, replace cover with foam insulation, secure with screws replace diffuser snaping in place. Recheck settings for desired temperatures.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Lawrenceburg, KY
- Parts Used:
- 12002497
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Drawer bar gear had a broken plastic piece that would not hold the bar in place
Looked at the appliance's booklet to see how it fit together, then installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Harwich Port, MA
- Parts Used:
- W11708403
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge door was opening too far / banging wall
took the fridge door off, took off old part that didn't work, replaced with new metal door stop (small part). Perfect-o problem solved with a $5 part! Customer Service here was AWESOME! THANK YOU! WILL SHOP HERE AGAIN.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pepperell, MA
- Parts Used:
- W11291138
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken light switch
Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.
Was this instruction helpful to you?
Thank you for voting!