WRFF3436RZ00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Margaret from Minneapolis, MN
- Parts Used:
- WPW10534155
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original refrigerator kick plate snap on connector broke and no longer able to keep kck plate in place
Pushed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Merced, CA
- Parts Used:
- WP67003405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Pivot Block not operating french door hinge
The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Warwick, RI
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
My refrigerator light did not work.
After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bath, ME
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Light in Freezer Compartment Out
Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Santa Rosa, CA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Very noisy when openning and closing
Part Select's easy to use website helped me fine the part quickly and tips on change out. It was so easy, I only regret that I waited so long to so it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Lawrenceburg, KY
- Parts Used:
- 12002497
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Drawer bar gear had a broken plastic piece that would not hold the bar in place
Looked at the appliance's booklet to see how it fit together, then installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard A. from Boones Mill, VA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Milk was freezing in Refig section, 28 F temp
Noted the Damper Assemby in the upper rear of refrig section,was always staying open during checks for problems. Controls appeared to be controlling temp changes when adjusted. Pulled the damper assemby after removing two screws holding the diffuser/cover(diffuser pops off with screwdriver) Damper assembly snaps out , unplug wires, snap new damper assembly in place, reconnect wires at the plug, replace cover with foam insulation, secure with screws replace diffuser snaping in place. Recheck settings for desired temperatures.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Palatine, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I broke the switch pulling the freezer basket out.
I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Santa Ana, CA
- Parts Used:
- W10830055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
a little problem with freezer gashet not fitting at top of drawer used hot wash rag to smoth it out.
Removed old gasket from right side of refrigerator and the bottom freezer doors. Reinstalled both gaskets to doors anbout 15 minutes in all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie E. from Elk Grove, CA
- Parts Used:
- W11028221
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
rust on the shaft in bottom drawer freezer
Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.
Was this instruction helpful to you?
Thank you for voting!