WRT511SZDW04 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Middletown, NY
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Evaporator Fan failure
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then removed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Crystal Beach, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lower refrigerator not cooling
Looked up problem in your troubleshooting section, determined necessary part, ordered part on Saturday. Received part Tuesday. Installed in about 10 minutes. Works great. Saved about $200.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arnold, MD
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
power surge killed the fan motor
Removed back panel in the freezer. Removed old fan. Installed new fan and reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from GIBSONTON, FL
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic on the shelf broke (too much weight in the drawer)
Remove the drawer. Remove top shelf it's connected to by carefully lifting. Turn the shelf upside down and slide meat drawer shelf off of either side, paying attention to how it is placed. Install new meat drawer shelf, replace shelf!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from CASTAIC, CA
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer was working fine but refrigerator would not go below 45 degrees
Removed back panel inside freezer replaced fan motor reinstalled panel and was done in about 40 minutes the video on part select explains the repair very accurately
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from ALVORD, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer working, not cold enough in fridge area.
Top freezer, remove fan cover on back panel in side top freezer, remove back panel inside top freezer, remove fan and fan motor, unplug electric from fan (PS unplug fridge first). Install new motor, replace ever thing in reverse. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from REDLANDS, CA
- Parts Used:
- WP2315539
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Our refrigerator fan motor stopped working.
Most important, remove bracket attached to freezer rear wall and put entire fan motor assembly together, including attaching power supply, ground wire, front bracket and fan blade (be sure rubber vibration dampeners are in place on both brackets) THEN attach the whole assembly to the rear freezer wall! Doing it this way is so much easier, and you won't run the risk of losing a screw behind the condenser, as I did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from NEWPORT, NC
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator fan in freezer.
I took the old fan out and replaced it with the new one,right easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from STEPHENVILLE, TX
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken drawer
Remove the food from the shelf above the drawer.
Slide the old drawer out and replace it with the new one.
Very easy fix.
Slide the old drawer out and replace it with the new one.
Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from KELSO, WA
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken meat drawer shelf frame...
Removed shelf, removed shelf frame and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from MONTROSE, CO
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the track for the meat drawer shelf cracked
We took out the shelf, the new track snapped in place easily.
Part Select is an innovative answer to dyo repairs, very
helpful through process.
Part Select is an innovative answer to dyo repairs, very
helpful through process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from POWAY, CA
- Parts Used:
- W11025586
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Track was broken on both front and rear mount
1)Removed the drawer
2) used a 8mm nut driver to unscrew the 2 mounting bolt.
3) clean /disinfect the bottom layer of the refrigerator
4) mount the track and installed the 2 #8 hex head mounting screw
5) slide back the drawer
2) used a 8mm nut driver to unscrew the 2 mounting bolt.
3) clean /disinfect the bottom layer of the refrigerator
4) mount the track and installed the 2 #8 hex head mounting screw
5) slide back the drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from San Francisco, CA
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original meat drawer broke due to overloading. I ordered from PART SELECT but had the agent help me with the exact item!
Getting the right part was the key but I had the serial number and the agent in Nova Scotia helped me identify the part and using the 360 degree camera, I was
able to determine how it was going to slide into the shelf. It took less than 15 minutes and was extremely easy to install. Everything just slide right in. The agent was the key to my success!
able to determine how it was going to slide into the shelf. It took less than 15 minutes and was extremely easy to install. Everything just slide right in. The agent was the key to my success!
Was this instruction helpful to you?
Thank you for voting!