WRFF3036RW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Stopped making ice
Initially I thought it was the valve that provides water to the ice maker. Days prior to go bad, it was making intermittent noises while filling the ice maker. I couldn't tell if it was the ice maker or not. It doesn't have a way to test it or reset button. So I decided and bought both parts, the valve and the ice maker unit. The installation was pretty straight forward. It takes ~30 minutes to replace. The ice maker ended up being the defective part. The one I got is a little bit different because it have a ON/OFF switch while the original did not. But everything else was exactly the same. Regarding the valve, it was good, so now I have a spare one in case it fails in the future. I'm glad I found this website to get the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NEWTON, NJ
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fridge was leaking water because of bad drain
Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues
Fixed the problem
Have had no more drain issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PT CHARLOTTE, FL
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Torn gaskets
Laid out new gaskets in sunlight to make them pliable. Removed old gasket by gently pulling them out of the channels around the door. I then did the reverse with the new gaskets. Starting at the top I pushed the new gasket into the channel, moving in one direction around the door. Make sure the outer lip of the gasket does not fold under itself. It should lie flat on the surface of the door. It is truly that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from GLOUCESTER PT, VA
- Parts Used:
- W11489993
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced left side guide on the freezer basket drawer.
Removed Phillips head screw on the front cover of both guides. Pull the drawer forward until it stops. Snap up the cover on each geared wheel to allow the basket to lift enough to continue removing the basket.
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel F from CALEDONIA, MN
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from NAPLES, FL
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Door Gasket Torn
Following the excellent video on Parts Select, we soaked the new gasket in warm water in the bath tub to make it pliable, then simply pushed it into the grooves on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryAnne from arroyo grande, CA
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Replace worn door gaskets
Viewed easy online instruction video. Laid gaskets on flat surface and warmed with hair dryer until they were smooth and unwrinkled. Starting at the top I pulled off the old gasket and beginning at the top I snapped in the new gasket. Carefully smooth as you go. I'm a 72 year old women and if I can do it, you can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Dublin, TX
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The refrigerator doors were not shutting well. . I would come home from work and the door would be a little ajar, but not beeping. The gaskets were cracked and worn.
I watched video provided on the part page. It was very easy to pull off the old gaskets. No tools needed. Also easy to push new gaskets into the grooves. I think it helped solve the failure to close program.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from HOPATCONG, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from TAYLOR, AZ
- Parts Used:
- W11173556
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken
Remove and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolee from Spokane Valley, WA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this instruction helpful to you?
Thank you for voting!