ABB2224BRB05 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from GEORGETOWN, TX
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke my original Kickplate Grille
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PASADENA, CA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center Crisper rail
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from Longview, WA
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I purchased a display model that was missing a part.
Snapped on the new toe grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henning from RHINELANDER, WI
- Parts Used:
- WPW10128551
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Refrigerator was warm,freezer was cold
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from SAMMAMISH, WA
- Parts Used:
- WP12227303WD
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My refrigerator vegetable bins were sagging when I placed veggies in it.
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from BATH, PA
- Parts Used:
- WP67002633
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked humid drawer
Complete replacement of the plastic drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joella from THE DALLES, OR
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The center rail was broken
The part just snapped in. super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathleen from GREEN VALLEY, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch in the freezer
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Santa Rosa Beach, FL
- Parts Used:
- W10443316
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice in the freezer/ condensation in the refrigerator
The icing n the freezer and wetness/ humidity in the fridge would not stop. I reasoned the freezer seal was bad and letting the outside humidity in. This fridge had been moved to the garage after a new one was put in my house. The new door seals completely fixed the problem, works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from COLORADO SPGS, CO
- Parts Used:
- W10121318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ICE BUILD UP AT BOTTOM OF FREEZER
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this instruction helpful to you?
Thank you for voting!