KBSD702MSS01 Whirlpool Refrigerator - Instructions

Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!

Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Recently unemployed, we knew a repairman was out of the question. We opted to glue the broken tab,but I knew that would just be living a substandard rerpair so looked on line. Found our replacement part very easily and much to our surprise we had the part the next day, yes, the next day!! Looking at the new part gave us the confidence to pop out the old one without causing damage to our unit. It was a no brainer , pop out and plug in w/in 30 seconds. Small appliance repairmen are a minumum of 75.00 service fee plus parts. Our repair less than 20.00 less than 24 hrs. How good is that?

Gail Costa

part got here fast and I fixed it in no time. GREAT Thanks

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

I popped the switched out depressing the underside of the switch so that it could be removed.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch into the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.

plugged the two wires in and snapped the switch into it's socket.

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.