MFB2055FRZ06 Whirlpool Refrigerator - Instructions

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

Unfortunately, I have still not managed to complete the repair, using the two parts indicated above, nor with the door bracket (part no WP2183805) that I ordered subsequently that arrived two days ago. It is not the same as, nor functionally equivalent to, the old bracket that I assumed was broken, since it was not retaining the piece in the base of the door into which the cam is inserted to mount the door. The new Cam is the correct part, but is not the solution since the old Cam is slightly worn but not damaged, and the thimble I bought does not seem to fit anywhere. The hole in the new bracket has a much too small hole to retain the Cam receptacle piece in place in the base of the door. However, this is the only lower door bracket shown in the PartSelect diagram of all the door parts used on a Whirlpool WRF560SMYM04 refrigerator. I do observe that the dark gray plastic cover on the base of the door is broken, but I don't imagine this plastic cover served to retain the Cam receptacle piece solidly in place, and this plastic cover is not offered as a replacement part either. At present I am at a total loss for how to proceed! However, the instructions for removing and replacing the door are clear and very easily carried out, and the job would be very quick and easy with the right parts. So beware if you are repairing the door on this model that the door parts diagram might not show all the parts to cover the door variations that apparently have been used!

I ordered both tracks for replacement. It was very simple to remove the glass shelf. Turn upside down and match the replacements to what is attached to the shelf. You need a butter knife or screwdriver to release the three clips connecting the track to the shelf. Very carefully press down on the clips to disengage and pull off of the shelf for all three clips. Line up thethe new part and push in until you hear it click in. That is all there is to it. Now you might as well clean the fridge.

A repair man came out and had to replace the ice maker

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Unplugged the refrigerator, removed the bottom freezer door, removed the two sliding shelves, removed the ice maker. Took the inside back wall off to expose the evaporator motor (have to bend it a bit to get it out. Used a small socket to remove the shroud and the evaporator motor. Installed the new motor and before putting it back together, plugged it in to ensure that the fan and motor worked. Then reassembled. Highly recommend knowing your brand and model#, and "Google" and YouTube it for additional help if you need it.

Easiest repair ever! Took maybe 5 minutes. Use the flathead screwdriver to push down on the three tabs holding the track onto the glass shelf and gently remove the old track. The new track snaps right in. Put the shelf back in the fridge, slide in the tray and it's done!

I read the other comments on how easy the repair was, followed their advice, and it worked like a charm. Just use a screwdriver or butter knife to pop the track off the shelf and pop the new one back in.

The hardest part was getting the items in the refrigerator out of the way!

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Unscrewed the old one and put the new one in
Some water on shelf of fridge
Overall not bad

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

Took the old one out & replaced it with the new one

The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.