WRF560SFHZ05 Whirlpool Refrigerator - Instructions

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Took the old ones out and replaced with the new ones.

Removed the door, removed the tray, removed the back bar(slipped the female cover off 1 side), removed the left slide, installed the new slide, installed the back bar, slipped in the drawer, popped the anchor back in the door with glue, installed the door and POW, it's done.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

That 1 Phillips screw out push up disconnect electrical plug put new one in by going in the opposite way.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

WITH PATIENCE! removal of door and old seal no problem! Followed the video- very clear. The part was difficult. Ornery plastic that needed to be softened and clipped (in comes the hairdryer and vaseline)- First corner great! the other 3 -patience. we set the door on a folding table with a towel on top to prevent scratches and ability to slide it around . inserting the dense plastic flange to clip under the seal was the most difficult . i approached the insertion from the opposite side so I was PULLING the seal into place with the base of a putty knife.( instead of my pushing fingers-70 arthritic- use tools to help!!
It took bit longer, a challenge- can be done, I am so happy i don't have to look for a new refrigerator!!!! Thank you for that instructional video which gave me the courage for the repair.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Using a screwdriver