ASI2575GRW12 Whirlpool Refrigerator - Instructions

Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

installed new parts

looked at the schematics from online

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.

We took the icemaker apart, and took pictures of how it looked before so we knew how to put it back together, we were really surprised how easy it was to put back together, I will be ordering other parts from this company, I got my part in 1-2 days by Fedex, I will be telling others about this company

Removed screws, Ice maker blads, and broken Auger Drum. Reverced order and replaced with new Auger Drum.

The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.