3XKGN7050F02 Whirlpool Refrigerator - Instructions

First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

On the bottom of the cover plate are two slots. Insert thin bladed screw driver and pry out gently. Remove electrical connection plate. Remove the old door by removing pin from spring and retaining bracket useing long nose pliers. Install new door kit making sure you use all the parts in the kit. The door buffer is different and the new kit does not require a heater.Install the electrical plate, ice shute and front cover.

The part came with minimal instructions .... "use all the parts in the kit". That is it.

Removed the top bracket (3 5/16 size hexhead bolts)
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.

I slid in the arm and slid in the ice bucket with augar.

The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?

Removed the drip tray under ice & water dispenser & removed 2 screws holding faceplate.
Unsnapped 2 microswitches that control ice dispenser & water dispenser.
Removed 2 screws holding control bracket, replaced with new one & reassembled.
Done!

Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into the slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

The ice guide slipped into place and latched into the arm with no problems. The nozzle went in so easy once I figured out that it was run through a tube in the door, I thought at first I was going to have to take the door apart. The biggest surprise was the how quickly I got the parts, I recieved in 1.5 days. Thats amazing. Thank You.

Stan

I unplugged the fridge, removed the face plate on the front, disconnected the power feeds, unscrewed the electrical panel and moved it out of the way.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.