WRT311FZDB05 Whirlpool Refrigerator - Instructions

Discovered that the fan in the freezer was not working properly. Removed the ice maker, paneling, wire harness and inserted new motor. Worked immediately and began circulating the cold air into the refrigerator.

i removed the back cover off in the icebox,removed the fan motor,replace the new one now it works fine.very easy to do,saved alot of money on a new one.

Removed the ice maker (3 screws) removed the back plate (2 screws) Remove the bracket holding the fan in (2 screws) Remove the rubber mounts on the old motor and the fan itself off the old motor. Then put it all back together in reverse order.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

Took the old fan motor out and installed the new one. Wow it's getting cool now. Thank You Parts select for the information on your site. Fast shipping. Very pleased I found your site, which stated it was the fan motor 45% of the time. It saved me from having to have a repairman come to my home. I called one but he did'nt work in this area. They gave me another man's number, and I called and left a message on the recorder, but he never got back to me. So I was happy to have found your site. Thank You again!

The fridge went warm and I noticed ice build-up on the freezer floor underneath the coils. I mistakenly thought that the defrost heater (or thermostat or timer) must have been the culprit. I used a voltmeter to test those components and chased a wild goose for quite sometime before realizing that the evaporator fan was not spinning and that it failed a test with the voltmeter. Replacing the fan easily fixed my problem! I later realized that the sheet of ice on the freezer floor indicated that the defrost cycle had been working. Were that not the case, the ice would have been all over the coils.

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.

first remove ice maker 1-screw on the bottom all the way out and two screws on the top half way out slide up and out and unplug wiring as you remove then remove back panel unplug ground wire remove screws that hold fan assembly unplug wiring remove pressed on fan blade put new motor in reasemble and it was good to go

the repair it good and easy ,vo helper to do it.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Following the info on another post from partselect site: Unplug the main refridgerator line from the outlet. Removed icemaker(didn't have this hooked up to operate), 2 screws and 1 hex nut; removed back panel of freezer wall (interior), be mindful of wiring harness on the left of panel, 2 hex nuts: unplugged fan motor from wiring harness, removed motor with 2 screws, gently, but firmly pulled fan blade off (a little tricky due to housing bracket around it) carefully noting 2 soft rubber gaskets that holds the unit in bracket. replace motor with new one ... follow above steps in reverse. helpful to have a small flashlight. make sure soft rubber gaskets are seated in place. Fan blade requires a firm but gentle push back on the metal post ... bottom of back panel seats over an opening in order for it to fit snug against the wall. I am totally satisfied with the info and seamless, expediant service with partselect ... thank-you so much ..

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.