WRF540CWHW09 Whirlpool Refrigerator - Instructions

replaced a door bin very fast

I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!

Remove existing bin by lifting up and out of refrigerator door. IInstall new bin by sliding into the door and pressing down onto the "clips" or attachments in the door. Done.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

had to remove shelving, crisper's, then unscrewed end cap. lifted it off set pin. and reversed for reinstallation. reefer door is reversed which makes it prone to close on crisper if not fully closed

Remove crisper and take off white front piece from old crisper and add to new one. Replace in refrigerator.

No tools needed. Snapped right into place, easy as could be.

This was actually very easy, take the two crispers out and the glass panel over the large drawer and the two holding brackets that hold the glass above.

then just use a nutdriver to remove the three nuts, gently pull the piece out and remove the slider with a screwdriver (two screws). Attach the slider to the new piece reinstall, it's very easy. Took 15 minutes tops.

This was for the left side the right side might be more problematic with the additional humidity controls I don't know ....

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

First I removed the pantry shelf and all the shelving on the bottom half of the fridge. I used the nut driver to remove the RH pantry end cap. Very easy. I took a picture with my digital camera to make sure that I remembered how the assembly looked when puttin git back together. Very easy to do. Common sense repair.

I'd been looking a broken plastic for 3 years. Googled Partselect on a whim and one week later a new drawer and lid arrived at my door. 10 minutes later the refridgerator was like new again.

With 2 babies and a chaotic household, i failed to double-check the measurements before I ordered the part. No fault of partselect, just user error ;-) I had to return the part bc i ordered the wrong size. Lesson learned, take my time and make sure it's done right the first time. The part fit in perfectly.
I used the search feature on the left side of the website to find the part, since the deli drawer wasn't in the parts diagrams given. The second time, customer service helped me find the part since the correct part wasn't on the website initially.
The deli drawer for this model is in the perfect place to have something dropped on it time and time again. I'm surprised you don't get more requests for this part to be replaced. It's bad design for Maytag to make it out of thin plastic.
Anyway, thanks so much for your patience in dealing with this frenzied mom! :-)

I removed the crisper drawers and glass shelf and set them aside. Used a nut driver (maybe 5/16") to unbolt the old endcap as well as the back piece which it was attached to. I had to study the damper system a bit so I could figure out how to put it back together, took some quick snaps with the digital camera to be sure I wouldn't flub it. I transferred all of the misc plastic bits which make up the damper system into the new endcap and bolted it back in.

First remove the snack drawer, glass shelf above it and other plastic pieces which just sit in place. Remove the three 1/4" screws that hold the end cap to the refrigerator liner. Lift up on the endcap and then out as there is a blind slot it slides into. Tilt the endcap out from the back and remove it. Remove the drawer glide from the endcap and transfer it to the new part. Reinstall the endcap by engaging the two plastic ends into the rear corner of the cabinet and then sliding it down on over the blind support. Install the three 1/4" head screws to secure the endcap to the liner. Reinstall the glass shelf and pantry drawer.