WRF535SWHW10 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Orlando from Bayonne, NJ
- Parts Used:
- WP2300868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one leaks on one side
Simply cut the water tube on both sides of connector and push in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from OCOEE, FL
- Parts Used:
- 67003900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clips on old part
Snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary C from CYPRESS, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken Plastic Pin
It was easier than I had anticipated. Just had to make sure that I was very careful in removing the old part so I did not break any of the good plastic that I needed in order to install the plastic temperature control to the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from LTL EGG HBR, NJ
- Parts Used:
- WPW10594329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
noise damper motor rattle
Very easy to fix . It was harder to empty the contents out or the refrigerator than to repair . The diagrams on this site were very helpful in identified the part. and it was delivered in 5 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank I. from FREMONT, CA
- Parts Used:
- WPW10326469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Center rail broke.
Removed the top glass above the vegetable drawers and slipped the center rail in place. And I would like to add that I would do business with this site again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. David from BRENTWOOD, TN
- Parts Used:
- WPW10350564
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Capacitor shorted out due to power surge.
Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Circle, MT
- Parts Used:
- W11024089
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Evaporator motor failed.
Remove lower freezer door from mounting frame (4 screws). Remove inner shelving and shelving brackets, Total of six screws, three on each side on lower brackets and 4 screws, 2 on each side on upper brackets. Remove ice cube maker (4 screws). Remove thermometer frame from back cover and slide thermometer out of frame. Remove 4 screws from back cover and remove cover. Slide thermometer through hole in back cover. Remove 4 screws from evaporator motor housing. Gently pull plastic fan off of motor shaft. Remove motor from housing and install new motor. Reinstall all parts in the order removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Southwick, MA
- Parts Used:
- WP67006704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass crisper top
Simple placement of new glass pane into crisper top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WATERBURY, CT
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Pin for drawer lid broke off
Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from MECHANICSBURG, PA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer iced up
Let the ice in the freezer melt while installing P trap drain tube
Was this instruction helpful to you?
Thank you for voting!
Broken drawer lid connector
I removed and replaced the right pantry end cap, as well as the drawer lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from BALD KNOB, AR
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber liner around the refrigerator door was splitting and cracking
I watched the video and it took away my trepidation. I did what it said and it went right in!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Blairsville, GA
- Parts Used:
- WPW10284685, WPW10284684
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Parts ordered on Sun Arrived Tues (local stores closed)
Talking with the service tech and youtube video it was a snap... Saved a service repair and a 25% parts mark up..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from RACINE, WI
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door gasket was cracked and torn
Replacement gasket extremely easy to install. Used hair dryer to soften and straighten out “kinks” in replacement gasket. Pulled old gasket out of groove in refrigerator door. Lined up corners of new gasket and pressed into place with my fingers. Went in exactly as video showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from JACKSON, WI
- Parts Used:
- WPW10594329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge had a clicking noise
Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.
Was this instruction helpful to you?
Thank you for voting!