WRX735SDHZ10 Whirlpool Refrigerator - Instructions

Recently unemployed, we knew a repairman was out of the question. We opted to glue the broken tab,but I knew that would just be living a substandard rerpair so looked on line. Found our replacement part very easily and much to our surprise we had the part the next day, yes, the next day!! Looking at the new part gave us the confidence to pop out the old one without causing damage to our unit. It was a no brainer , pop out and plug in w/in 30 seconds. Small appliance repairmen are a minumum of 75.00 service fee plus parts. Our repair less than 20.00 less than 24 hrs. How good is that?

Gail Costa

part got here fast and I fixed it in no time. GREAT Thanks

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

plugged the two wires in and snapped the switch into it's socket.

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Remove plastic vent cover. Just snaps out. Take out two screws that hold damper cover on. Unclip and unplug damper assembly. Snap in new assembly and plug in. Replace covers. I was pretty sure this would fix my problem after observing the damper for several days. It would stay open and when I moved it by hand it would open a little more and then close. Easy fix!

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.