WRX735SDHW09 Whirlpool Refrigerator - Instructions

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!

Looked at the appliance's booklet to see how it fit together, then installed it.

Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)

Noted the Damper Assemby in the upper rear of refrig section,was always staying open during checks for problems. Controls appeared to be controlling temp changes when adjusted. Pulled the damper assemby after removing two screws holding the diffuser/cover(diffuser pops off with screwdriver) Damper assembly snaps out , unplug wires, snap new damper assembly in place, reconnect wires at the plug, replace cover with foam insulation, secure with screws replace diffuser snaping in place. Recheck settings for desired temperatures.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

watched the video how to remove, and did it.

Popped the cover to expose the part. Then removed two screws and unplugged the part. Exchanged the new part for the old. Plugged the new part in and replaced the screws And the cover.

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.