WRF540CWHW08 Whirlpool Refrigerator - Instructions

Removed the freezer door, by loosening 4 screws and pulling upwards to disengage door from frame. Removed the top basket by pulling up on both slides on the gear shaft sides, note they have retaining tabs you must push in. once the slide / guards are up the top basket comes out. Remove the bottom basket. Remove to angled screws on the top tracks and remove. Remove 6 screws on bottom slides, 3 per side and slide out as a whole unit. Unplug the ice maker, remove 3 screws for it to come out. Note I cleaned mine while it was out with vinegar to remove the mineral build up on it. Remove the screws in the back panel, and pull it forwards. The top vent has 2 clips that hold it in and you will need to remove it prior to fully removing the plate. The plug for the icemaker needs to be removed also. Pull the back plate out. Once the plate is out you can see the fan and access it. Unplug the clips that hold the wiring harness secure. 2 screws to remove the fan assembly. Once fan assembly is out, disassemble it, then reverse assemble it with new parts and fire it up. Mine took right off and running like its brand new.

Had to use heat, somebody said to put in dryer before installation

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Actually shouldn't you have included installation instructions with the product?
I had to search for installation instructions on Utube or the job would have ended in another cracked crisper frame.

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

No tools needed. Snapped right into place, easy as could be.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Remove existing bin by lifting up and out of refrigerator door. IInstall new bin by sliding into the door and pressing down onto the "clips" or attachments in the door. Done.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

had to remove shelving, crisper's, then unscrewed end cap. lifted it off set pin. and reversed for reinstallation. reefer door is reversed which makes it prone to close on crisper if not fully closed

Remove crisper and take off white front piece from old crisper and add to new one. Replace in refrigerator.

I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!

This was actually very easy, take the two crispers out and the glass panel over the large drawer and the two holding brackets that hold the glass above.

then just use a nutdriver to remove the three nuts, gently pull the piece out and remove the slider with a screwdriver (two screws). Attach the slider to the new piece reinstall, it's very easy. Took 15 minutes tops.

This was for the left side the right side might be more problematic with the additional humidity controls I don't know ....

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

First I removed the pantry shelf and all the shelving on the bottom half of the fridge. I used the nut driver to remove the RH pantry end cap. Very easy. I took a picture with my digital camera to make sure that I remembered how the assembly looked when puttin git back together. Very easy to do. Common sense repair.