WRT148FZDW05 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from BUFFALO GROVE, IL
- Parts Used:
- W10861519
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The original shelf that came with the refrigerator broke and we ordered a replacement.
The problem with the replacement part is that it didn't fit cleanly and doesn't slide well with the existing drawer.
We were disappointed.
We were disappointed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from RIDGEFIELD, NJ
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Bottom part of refrigerator wasn't getting cold
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out
You guys are the best.
Called in and you guys helped out
You guys are the best.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BONNEAU, SC
- Parts Used:
- W11229610
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET AROUND DOOR WAS LETTING AIR IN/ COLD AIR OUT
Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aida from HOMESTEAD, FL
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
broken meat drawer ;shelf
When I did not see instructions on how to replace the broken shelf that holds the meat drawer, I was afraid it would be difficult but after seeing how the broken piece placement was placed all I had to do was slide it off and place the new one. No problem, Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from ELMWOOD PARK, NJ
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Meat drawer shelf broke
Slid the shelf onto the track
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CROWNSVILLE, MD
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Meat drawer shelf broken
Pull the top shelf out and slide the new part in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from WASCO, CA
- Parts Used:
- WP2163777
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doesn’t cool
Work just perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from N TONAWANDA, NY
- Parts Used:
- W11193484
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I broke the cooling fan while cleaning the heat exchange area
Very simple, pulled old fan blade off and pushed new fan blade onto shaft. Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from woodland hills, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
you have to turn it off and on to run.
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dunmore, PA
- Parts Used:
- W11745278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Renton, WA
- Parts Used:
- WP2315539
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator fan needed replacing
I actually followed the instructions by William. He did a great job. I ran into some difficulty because the wire connector on the replacement motor didn't match the old connector. We had to replace the connector on the new motor to match the wiring harness, which was easier than trying to match the connector on the motor. Had the connectors matched, the replacement would have taken less than 30 minutes to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffry from peabody, MA
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
the fride section was not geeting cold the Fan was not turnin on
first remove ice maker 1-screw on the bottom all the way out and two screws on the top half way out slide up and out and unplug wiring as you remove then remove back panel unplug ground wire remove screws that hold fan assembly unplug wiring remove pressed on fan blade put new motor in reasemble and it was good to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Skyler from San Marcos, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer running, yet fridge warm.
The fridge went warm and I noticed ice build-up on the freezer floor underneath the coils. I mistakenly thought that the defrost heater (or thermostat or timer) must have been the culprit. I used a voltmeter to test those components and chased a wild goose for quite sometime before realizing that the evaporator fan was not spinning and that it failed a test with the voltmeter. Replacing the fan easily fixed my problem! I later realized that the sheet of ice on the freezer floor indicated that the defrost cycle had been working. Were that not the case, the ice would have been all over the coils.
Was this instruction helpful to you?
Thank you for voting!