4YET20DKAN01 Whirlpool Refrigerator - Instructions

Removed correct part from those provided and slipped it into position. No tools necessary.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Simple. snap together instalation, no tools required. Thank you partselect for having the parts pictured with a size grid in the background, without that size grid, it would have been more difficult to select the right part. And, may I add, "my local appliance repair person indicated- he could not locate a repair part." I found the part via google search, and partselect.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

It was an easy repair. The side hinge plate had two fasteners on it. One which was hooked shaped and the other was pointed. I took the plate and installed the hooked shaped fastener first into the rectangular cutout and then pushed the plate with the pointed fastener into the circle cutout. Checked to see if the plate was fastened and once it was the repair was done.

My wife removed the broken Grille and replaced it with new Grille without using any tools. She was aware of how to remove and replace the grille as she has done it over the years when cleaning under the refrigerator.

UN plugged refrigerator,waited 24 hours to let defrost,removed panels,cut out old Bi metal Defrost thermostat,wired in new thermostat,reassembled freezer,plug back in,working great

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.

Cover the entire metal retainer bar in painter's tape (the blue one) and use a 20-22" hacksaw to cut it to the correct length, going very slowly in your sawing.

I followed the instructions sent with the piece and VOILA it was repaired in less than 5 minutes. The whole process from finding the part of the web site to the ordering to the arrival of the part to the repair was so wonderfully simple. THANK YOU!!!

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

Replaced bracket-amazed to find how quickly I was able to id the part on this 20 year old refrigerator. Ordered the part and received it the next day! Thanks for the good service! , Bob

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!