ART318FFDW01 Whirlpool Refrigerator - Instructions

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

First i pulled the electrical plug from the socket so the refrigator was off than I removed 5 screws (3 of those holding the ice maker). pulled the icemaker toward the front and removed it I than took off the back of the freezer panel,(the back panel was removed by pulling the top of the panal towards me it came right out of the freezer) I removed an additional 2 screws holding the evaporator fan motor. Than I used pliers to squeeze the mounting bracket tabs (white tabs BOTTOM OF MOTOR BRACKET). I then disconnected the electrical FAN MOTOR PLUG and removed the motor. i than pulled the fan blade from the motor (fan blade is only a pressed onto the motor shaft.I than pressed the fan blade back unto the fan motor and reversed the above directions

Removed the ice maker (3 screws) removed the back plate (2 screws) Remove the bracket holding the fan in (2 screws) Remove the rubber mounts on the old motor and the fan itself off the old motor. Then put it all back together in reverse order.

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( quite easy )

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

Following the info on another post from partselect site: Unplug the main refridgerator line from the outlet. Removed icemaker(didn't have this hooked up to operate), 2 screws and 1 hex nut; removed back panel of freezer wall (interior), be mindful of wiring harness on the left of panel, 2 hex nuts: unplugged fan motor from wiring harness, removed motor with 2 screws, gently, but firmly pulled fan blade off (a little tricky due to housing bracket around it) carefully noting 2 soft rubber gaskets that holds the unit in bracket. replace motor with new one ... follow above steps in reverse. helpful to have a small flashlight. make sure soft rubber gaskets are seated in place. Fan blade requires a firm but gentle push back on the metal post ... bottom of back panel seats over an opening in order for it to fit snug against the wall. I am totally satisfied with the info and seamless, expediant service with partselect ... thank-you so much ..

i removed the back cover off in the icebox,removed the fan motor,replace the new one now it works fine.very easy to do,saved alot of money on a new one.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.