ET2GTKXKT00 Whirlpool Refrigerator - Instructions

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.