GZ25FSRXYY Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from OLYMPIA, WA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy damper
Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SYLVA, NC
- Parts Used:
- W10882923
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
ice maker quit
For this repair, the following YouTube video was most helpful in showing how to remove the ice maker from the refrigerator model that I have: for some reason this site has deleted my video cite but it is the YouTube video cite that ends in 7HHH03SFdCA Next, because the electrical wiring harness part has changed since production, and the new ice maker part comes with two different harness' (you have to determine which one is most similar to the harness that you remove), take a lot of pictures of the old wiring harness before removing it. There are a lot of different wires that need to be reconnected. There was a prior post by "Greg from Aliso Viejo, CA" that I printed out and followed--that post was also very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from EXPORT, PA
- Parts Used:
- W10882923
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice tray sticking. No ejection of ice. Motor not working properly
Took out ice maker. Then unscrewed tray after opening old turn motor clock panel and carefully detaching wires from socket(s) where needed. Put in and screwed in new tray with the new motor clock. Replaced wires into new sockets. Put the whole maker back into place. Makes great ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from MIDLOTHIAN, VA
- Parts Used:
- WP67006331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
A cover over the water filter was broken
The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arja L. from NEWBURY PARK, CA
- Parts Used:
- WP67006331
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Snap on cover broke
Saw U tube instrctions how to install and it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WALLA WALLA, WA
- Parts Used:
- WPW10300024
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MERRITT IS, FL
- Parts Used:
- W10882923
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
ice maker burned out
you tube video was most helpful. after getting new part and disassembling old ice maker, you have to change out the wiring harness. Reinstall ice maker, don't worry about the timing of the unit as it will do this itself, may take 10 hours to produce ice, mine took about 2 hours to go through its' cycles and give me ice. It is running great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from Leander, TX
- Parts Used:
- W10882923
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Not Making Ice
Pulled the whole assembly out and unscrewed the Ice maker and old wire harness loose. pulled one wire at a time loose and put the new one in place one wire at a time so not to get them wrong. Then the ground wire I cut and stripped and used a wire nut to connect the two green wires together. Otherwise you would have to take more things off to get to the 1/4 nut on the ground wire. Then put the three screws back in the ice maker bottom.Slid it back in place and plugged in the new wire harness. And put the plastic cover back in place to cover the wires. You can also look on U-Tube to see how it is done. They just do not show the new harness I was sent. I guess the ice maker I got fit other models.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Goldsboro, NC
- Parts Used:
- WPW10714545
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer door leaking on floor.
Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from AVONDALE, AZ
- Parts Used:
- W10882923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water coming from ice dispenser
First found U Tube video of my exact refrigerator, ice maker remove and replace. Many available, all are helpful. Watch several times. Once part arrived the repair went very smoothly. Only had some difficulty attaching the ground wire, had to loosen the auger motor to attach the tiny screw. Not difficult, just took a bit of time to get the angle on the screw correct.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from OTSEGO, MI
- Parts Used:
- WPW10300024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Would not make ice.
Removed the whole ice maker unplug one wire harness replaced ice tray with new one.
Very simple.
Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- laurie from gold canyon, AZ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is almost embarassing but you asked....
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Paola, KS
- Parts Used:
- WPW10498990
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench set
crack in inlet valve
took old inlet valve off put new one on hooked up ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CAPE CORAL, FL
- Parts Used:
- WPW10714545
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket was old and air leaking into freezer !
Took off old one and just replaced new, very easy and corrected problems!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from SCOTTVILLE, MI
- Parts Used:
- W10882923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Unplug and remove existing wiring harness and old ice maker if need to.
Got lucky ordered new ice maker then current one started working again ???????
Was this instruction helpful to you?
Thank you for voting!