WRT318FZDM07 Whirlpool Refrigerator - Instructions

Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

Removed door and replaced bushing bracket was ok.

Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!

The problem with the replacement part is that it didn't fit cleanly and doesn't slide well with the existing drawer.
We were disappointed.

$80 part motor fan replaced saved me $1000 or more on new fridge.

Called in and you guys helped out
You guys are the best.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

After left side track broke 3 times and then center track also broke, I got tired of buying replacements (even though they are easy to install and not very expensive). So I bought a tube of plastic epoxy and a bit of fiberglass cloth and reinforced the plastic that the (#8 x 1/2 inch) screws go through (where it breaks) on ALL 3 tracks, then redrilled holes, added a washer, and used #8 x 5/8 inch screws). Maybe these wiil last.

After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.

When I did not see instructions on how to replace the broken shelf that holds the meat drawer, I was afraid it would be difficult but after seeing how the broken piece placement was placed all I had to do was slide it off and place the new one. No problem, Thank you!!!

Slid the shelf onto the track

Very simple, pulled old fan blade off and pushed new fan blade onto shaft. Perfect fit!

Work just perfect

Pull the top shelf out and slide the new part in

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.