2VET21DKJW01 Whirlpool Refrigerator - Instructions

Repair was very easy. We removed the glass from the shelf above the crisper drawers and then just snapped the rail into the frame.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

The repair was very simple! And the website was also easy and accurate to use! I put the new rail in after taking out the glass shelf ( just like you do when you clean it) and snapped in the new piece. Voila! sliding drawers again.

removed the lower door. took out the old gasket, snap in the new one. piece of cake.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

poured boiling hot water into drain; removed most ice with hair dryer. Clips(2) positions the defrost tray & drain under the freezer condenser. A "home-made" coil of 18g copper wire inserted into the drain hole, & secured to the defrost heater further prevents the drain from iceing shut!

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

I removed the screws on top of the refrigerator and the freezer door, lifted the fresh food door off bottom hinge laid it on a covered floor, used a pair of wire cutters to cut old gasket. then pulled the gasket straight out all the way around. then I started on one corner using a putty knife to push the new gasket under plastic trim, then put gasket on opposite corner at top of door then did the same with other two corners, then used putty knife to go all the way around sliding gasket under trim. was easy.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

Wood on floor, used a screwdriver to lift weight off caster's with one hand and screwed the screw in with the other hand. Repeated these steps to do the other screw into remaining caster.

the repair it good and easy ,vo helper to do it.

Ordered new drawer. New drawer seems to be better than factory drawer (slightly thicker). Removed old, removed white handle from old (ran hot water over old to make it less prone to cracking when prying off), pushed old white handle onto new drawer, inserted new drawer, done. New drawer is great; better construction. Thanks.

1.Slid out old cracked drawers 2.Slid in new crisper drawers Simple! It took longer to open the shipping boxes than to install the new drawers! Problem solved! If only all fixes were this easy!!