WRS315SDHZ0A Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Fairfield, OH
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
ice was not moving into door crusher
First I removed the 6 screws and then 2 more--being carefull to take cap off inside to nremove metal blades--be sure to keep in order--taking ba digital picture helps at this point--make sure to put back nin reverse order after replacing washer and new auger--went smooth thanks appliance parts repair service forum--Rick--Enjoy your own repair!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CAMPOBELLO, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice bin auger drum was broken
removed ice bin from freezer then removed front from ice bin then all i had to do was remove e clamp from end of shaft that made it possible for me to remove the ice crusher parts then slide off the drum. all that was left was to put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B G from lindale, GA
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no ice dispensing
removed ice storage drawer, removed dispensing shaft from storage drawer, replaced plastic auger and reassembled.
quick and easy....
quick and easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from San Ramon, CA
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice not dispensing
This was not a hard repair. Just remove all the screws and slide out the old Auger drum. It is always good to take a picture first incase you have any problems putting it back together. Be careful to put the ice crushers back in the same order and make sure you look at how the "door spring" connects before pulling it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from Clyde Park, MT
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice would not dispence because drum was broken.
Repair was easy enough, take apart and put it back in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Palm Coast, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Bin Auger Drum was broken.
Removed screws, Ice maker blads, and broken Auger Drum. Reverced order and replaced with new Auger Drum.
The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.
The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Florence, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The auger drum broke from the shaft
I removed the 4 screws holding the front cover in place. Removed the 4 screws holding the ice auger cover in place. Removed the c clip holding the auger on the shaft. Pulled out the auger shaft. Removed the broken auger drum and replaced with the new one. Reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREY from DUBBERLY, LA
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
perfect
remove the ice container. and i got to work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- debbie from Shepherdsville, KY
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
would not dispense Ice
Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Racine, WI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch broken
I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SPRINGVILLE, AL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch Controlling Light When Door Open Was Briken
Poped ou the old switch, connected new switch and pushed back into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Buffalo, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke plastic tab on auto light switch
Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from Katy, TX
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The auger drum had detached from the shaft (broke off).
I removed the external shaft that controls the ice grinder. Its spring loaded so you have to remember how to get it back together. I removed the screws that hold the cover in place. I removed the nylon nut that holds the drum and grinder on the center shaft. I replaced the drum and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geneva from jennings, LA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wouldn't feed ice
auger blade was replace
Was this instruction helpful to you?
Thank you for voting!