JUCFP242HL00 Whirlpool Refrigerator - Instructions

Removed two screws, pulled the element out and disconnected the wire harness. Reversed the procedure and we were one.
Kept a close watch n the ice maker to make sure we didn't have another flood. The first time an ice cube stuck between the metal bale and the side of the freezer--we had about 50 gallon of water on the floor. Thought we had it fixed and a few days later another flood. Decided to replace the unit and it is working great...Hopefully no more floods.

3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

I watched the recommended you tube video multiple times. I made sure to have the tools and towels ready. I shut off the water supply line, and capped it, removed the backing, and inspected the back. By following the video, the rest was easy. I recommend removing any built up dust and dirt while you have the front apart.

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

First I tried repairing the but that did not work, so I looked online and found partselect.com, put in my part number and wammo! There it was, the same exact water inlet line, and reasonably in-expensive. I ordered it and it got here pretty quick.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

I watched the video on your site and it made it very easy, thanks

Directions say to remove tube from filter inlet, but could only get one arm under the refrigerator. Connection was located about dead center under the box. Was much simpler to remove the two screws at the front that hold the filter itself in place. Whole unit slides right out and was 10 seconds to pop out old tube and insert new tube.

Replaced the supply line following the directions supplied by the video that was provided with the part order. I could not have done it as well an in the short amount of time required without the aid of the video. I would not have known that the water filter housing/unit had to be removed to facilitate the repair.