JFC2290RTB03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lee Ann from College Station, TX
- Parts Used:
- W10436252
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Frost on the top edge of the freezer drawer
Put the gasket in the dryer for 15 minutes to warm it up. It fit much better after it was warm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margie from DERBY, KS
- Parts Used:
- W10436252
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer gasket not sealing.
Watched video on line.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HARRISBURG, PA
- Parts Used:
- W11346623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Head filter broke where you put the filter in
I watched a 5-minute YouTube video ordered the part. It was delivered fast and it took me about 30 minutes to put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henning from RHINELANDER, WI
- Parts Used:
- WPW10128551
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Refrigerator was warm,freezer was cold
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STOCKBRIDGE, MI
- Parts Used:
- W11346623
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ICE MAKER WATER FILTER HEAD REPLACEMENT
AS PER A VERY GOOD VIDEO I FOUND SIMPLY BY SEARCHING FOR THE PART NUMBER. IT MAY HAVE BEEN ON THIS SITE. SADLY, THE PUSHING ON THE CONNECTOR WITH THE 1/2" WRENCH LOOKED A LOT EASIER IN THE VIDEO, OTHERWISE EASY PEAZY AND I HAVE VERY PAINFUL ARTHRITIS IN MY SHOULDERS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from WARREN, RI
- Parts Used:
- WPW10420083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
No water and ice maker not working
Used a 1/4" nut driver for the project install, just one note when installing the water feed into the new inlet valve make sure it is seated properly, look for the indicator mark on the water feed. Very easy installation!
Was this instruction helpful to you?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MABLETON, GA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from New Johnsonville, TN
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch broke.
Couldn't figure out how to get the old one out till I saw the new one.Pop the old one out slide the 2 wires on the new one pop it back in place,good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Pensacola, FL
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY A from PITTSBURGH, PA
- Parts Used:
- WP67002321
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
"Gourmet Bay" had only one divider. Contents were getting feisty..
Opened package. Washed divider. Dropped in place (where indicated by marks) in drawer. Took a nap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marybeth from VACAVILLE, CA
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap for filter
Bought new cap.
Was this instruction helpful to you?
Thank you for voting!