MFI2269FRB03 Whirlpool Refrigerator - Instructions

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP

It was so easy. One small screw on the center hinge, slip the electrical connection off of the old one then slide the mullion off of the top and bottom connections. After sliding the new one on and connecting the electrical just screwing in the screw and done. It works perfectly.

Pried out the old switch and installed the new switch.

Can not do repair. Ordered part 3/30 due to me on 4/1. Today is 4/15 and still no part. I even paid for quicker delivery. Thanks FedEx!!

Just simply put the new bin in the spot reserved for it on the refrigerator door.

made a call and I was taken care of immediately

remove two crispers and glass top . Replace rail.
Note
This is 3rd time this part in about 5 years has needed replcement. If there is a next time I would expect a "freebe". Service is great and replacement rail came in jig time.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Watched a couple of videos. Removed left side hinge first, then did the same to the right side hinge. Part was installed in reverse order. Installation took less than 60 seconds.

In less than 1 minute I put the crisper glass in place. I wa overwhelmed at the speed in which I received this part. It was ordered on monday evening and I received it on wednesday morning. PartSelect was a life saver as the repair was just day before Christmas.

The repair was very simple, just put the parts in place. We were very please with the quick shipment and the good prices.

Watched the video. Everything went great, Super simple