KRMF706EBS04 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from Portland, OR
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light Switch Broken
Removed old light switch by prying up and out of housing...removed wires (carefully not to get shocked!) and taped to inside of refrigerator housing. Ordered best matching part and rec'd it in a couple of days. Took less than 5 minutes to remove taped wires from side of cabinet and connect to new switch (which was a perfect match to the original equipment) and snap switch back into refrigerator housing! Works perfectly! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hinsdale, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Light switch cracked Mounting
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlane from Harriman, TN
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator light switch broke to pieces
Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from Tempe, AZ
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Light Switch
Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time
5 minutes Total Time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from middle island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light would work intermitently
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from haverstraw, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replace Bad Switch
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JONATHAN from ELKINS PARK, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STANLEY from OAKLAND, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rocker switch broke off
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Branson, MO
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
switch was broken
I popped the switched out depressing the underside of the switch so that it could be removed.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch into the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch into the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Jefferson Hills, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WAYNE from KENNERDELL, PA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch was accidently hit and broke.
plugged the two wires in and snapped the switch into it's socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Flagstaff, AZ
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light went out
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!