WRX735SDHB03 Whirlpool Refrigerator - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This is definitely one of the easiest, most rewarding projects I've ever done! From the point of easy ordering to receipt of the part in just two days (!!!!), opening the box was probably more effort than clipping the part in place! I'm keeping partselect on my favorites list!

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Remove plastic vent cover. Just snaps out. Take out two screws that hold damper cover on. Unclip and unplug damper assembly. Snap in new assembly and plug in. Replace covers. I was pretty sure this would fix my problem after observing the damper for several days. It would stay open and when I moved it by hand it would open a little more and then close. Easy fix!

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

Popped the cover to expose the part. Then removed two screws and unplugged the part. Exchanged the new part for the old. Plugged the new part in and replaced the screws And the cover.

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

It was very easy I just push ito n and it snaped right in.

Part Select's easy to use website helped me fine the part quickly and tips on change out. It was so easy, I only regret that I waited so long to so it.

Received the grille and placed it in it's place. Not difficult at all.

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.