WRT519SZDW06 Whirlpool Refrigerator - Instructions

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

replaced old one installed new one