WRS586FIEM05 Whirlpool Refrigerator - Instructions

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!

ONCE WE KNEW THE COMPRESSOR WAS NO LONGER FUNCTIONING , USED A MULTI METER TO VERIFY 120 VOLTAGE TO THE INVERTER WAS PRESENT, FOUND 120 VOLTAGE TO THE INVERTER WITH NO VOLTAGE TO THE COMPRESSOR. OHMS OUT THE COMPRESSOR, FOUND IT WAS WITH IN SPECS. REPLACED THE INVERTER AND ALL IS WELL ONCE AGAIN.

Removed freezer cover from ice maker, unplugged the harness. Installed the new ice maker assembly,plugged in two wire harness and secured the part and cover.
Results was smooth process, no noice from ice dispenser. Pleased with results. Saved on repairs. Thanks Tom

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.

Simple to replace. 6 screws out. Unplug connections... Plug back in, replace screws.

Unfortunately still not making ice. Will try fill valve replacement.

First turn off the ice maker. Then there's four screws in the very back you remove pull out the cover. There's hex head 516 bolts maybe quarter inch that hold in the ice maker unplug the ice maker reverse process

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

The repair went great, however, I had someone to put the part in for me.

Did my homework.
Consulted Utube
Bought the part
Installed

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!