WRF550CDHZ03 Whirlpool Refrigerator - Instructions

Remove crisper and take off white front piece from old crisper and add to new one. Replace in refrigerator.

No tools needed. Snapped right into place, easy as could be.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

I'd been looking a broken plastic for 3 years. Googled Partselect on a whim and one week later a new drawer and lid arrived at my door. 10 minutes later the refridgerator was like new again.

First I removed the pantry shelf and all the shelving on the bottom half of the fridge. I used the nut driver to remove the RH pantry end cap. Very easy. I took a picture with my digital camera to make sure that I remembered how the assembly looked when puttin git back together. Very easy to do. Common sense repair.

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

This was actually very easy, take the two crispers out and the glass panel over the large drawer and the two holding brackets that hold the glass above.

then just use a nutdriver to remove the three nuts, gently pull the piece out and remove the slider with a screwdriver (two screws). Attach the slider to the new piece reinstall, it's very easy. Took 15 minutes tops.

This was for the left side the right side might be more problematic with the additional humidity controls I don't know ....

It was great! Took my husband less then 5 minutes to fix. Your delivery time is excellent. This is the second time I order from you and would do so again if the need arises. Thank you so much. Don't be afraid people go ahead and order.

I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!

With 2 babies and a chaotic household, i failed to double-check the measurements before I ordered the part. No fault of partselect, just user error ;-) I had to return the part bc i ordered the wrong size. Lesson learned, take my time and make sure it's done right the first time. The part fit in perfectly.
I used the search feature on the left side of the website to find the part, since the deli drawer wasn't in the parts diagrams given. The second time, customer service helped me find the part since the correct part wasn't on the website initially.
The deli drawer for this model is in the perfect place to have something dropped on it time and time again. I'm surprised you don't get more requests for this part to be replaced. It's bad design for Maytag to make it out of thin plastic.
Anyway, thanks so much for your patience in dealing with this frenzied mom! :-)

First, turn off the refrigerator so the open door alarm doesn't drive you crazy while you are working with the refrigerator doors open! Then, remove both crisper drawers, remove deli drawer, remove deli cover from two pins (one was already broken), remove the bottom glass shelf and the plastic glass support. None of this requires any tools, all just slide or lift out. Then, using a nut driver remove the two screws holding the drawer slide from the pantry end cap. You access one of the screws from an opening while the slide is all the way in. This is where I needed needle nose pliers to remove the screw from the opening after it was unscrewed - if your nut driver is magnetic you won't need the pliers. To access the second screw, pull the slide all of the way out. Then you remove the broken end cap by unscrewing 3 screws with the nut driver. Once the screws are removed, you lift up on the front of the end cap to loosen it from a catch on the inside and then pull the end cap out. Install the new end cap by sliding the two tabs into the back of the refrigerator and then pushing down on the end cap to set it in the catch. Now replace the screws, re-attach the slide with the two screws, reinstall the glass and the drawers and then reinstall the drawer cover by slipping it into the pins on each side (be careful when depressing the pins, do it gently or they may break off). Turn the refrigerator back on. You are done These instructions make it sound much more difficult than it actually is, it takes as long to remove and replace the drawers and it does to do the actual installation of the end cap..

with screw driver, pry up white upper drawer border and cover carefully. Place over new drawer in same location on a hard surface. press the upper border over the new drawer and press downward.carefully until it snaps in place. insert drawer in old drawer location.

extremely easy to replace, just snap off the white frame and snap on the new one.

First remove the snack drawer, glass shelf above it and other plastic pieces which just sit in place. Remove the three 1/4" screws that hold the end cap to the refrigerator liner. Lift up on the endcap and then out as there is a blind slot it slides into. Tilt the endcap out from the back and remove it. Remove the drawer glide from the endcap and transfer it to the new part. Reinstall the endcap by engaging the two plastic ends into the rear corner of the cabinet and then sliding it down on over the blind support. Install the three 1/4" head screws to secure the endcap to the liner. Reinstall the glass shelf and pantry drawer.