WRF532SNHZ06 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helene from Matawan, NJ
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ladder hook for shelves broke.
Hook just clips right into the channel in seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willie from LOUISBURG, NC
- Parts Used:
- W10830162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad door gasket
pull out old gasket and pushed in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from WYNNEWOOD, PA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rail snapped
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from WILMINGTON, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
Lift off glass shelf and insert tabs of rail on each end , replace shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from WORCESTER, MA
- Parts Used:
- WPW10289497
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
fridge door bin came of and broke as I was getting out a gallon of milk
Pushed it in just as the old one came off and broke. Took 10 seconds. Push and play!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel F from CALEDONIA, MN
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from JOLIET, IL
- Parts Used:
- WP67002633, WP67001716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
BOTH THE LADDER HOOKS, AND THE CRISPER PARTS WERE BROKEN
SIMPLY REPLACED THEM
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from GLOUCESTER PT, VA
- Parts Used:
- W11489993
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced left side guide on the freezer basket drawer.
Removed Phillips head screw on the front cover of both guides. Pull the drawer forward until it stops. Snap up the cover on each geared wheel to allow the basket to lift enough to continue removing the basket.
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE from WEST PALM BCH, FL
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had no problem
Just take the crisper out and just put it in the hall access
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Bismarck, ND
- Parts Used:
- WPW10655367
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
drip pan was cracked
Removed rear cover, removed fan and than drip tray. install new tray and reassemblied
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!