WRS325SDHZ04 Whirlpool Refrigerator - Instructions

Three 1/4” nutdriver screws and a small plug in the rear of the icemaker. Installed in minutes, performed a reset. Working fine.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

I removed the back cover that protected the motor and water inlet valve. Removed the screws that held the inlet valve to the refrigerator. Then I took a picture of the wiring and water lines on the inlet valve so I would make sure that I hooked up the new inlet valve properly. When I received the new inlet valve I removed the back cover which I had replaced and installed the new valve. It was a very easy process.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

I took the white slim pipes off the brackets. Put the white pipe in the hole in the freezer and push the glass into the brackets. Repeat again..

Pried out the old switch and installed the new switch.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.

installed new parts

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

removed six screws removing the cover and exposing the shaft & auger.

I then had to remove the snap ring & undid the end nut that has left handed threads.removed the 6 auger plates and then replaced all parts in reverse order of their removal.

Once I removed the ice bin from the freezer section of refrigerator and removed all the necessary screws was able to remove the auger drum, but had some difficulty in reinstalling the crusher blades in the dispenser. After several tries, got it right and dispenser is performing like new.

This was not a hard repair. Just remove all the screws and slide out the old Auger drum. It is always good to take a picture first incase you have any problems putting it back together. Be careful to put the ice crushers back in the same order and make sure you look at how the "door spring" connects before pulling it apart.

removed ice storage drawer, removed dispensing shaft from storage drawer, replaced plastic auger and reassembled.

quick and easy....

remove the ice container. and i got to work