WRS321SDHB05 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SWAINSBORO, GA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Auger Drum broke
I followed the instructions on your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SACRAMENTO, CA
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Installed Ice Maker in Freezer
Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from HOPATCONG, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerby from BEVERLEY HILLS, FL
- Parts Used:
- WPW10169511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice dispenser not working.
All I did was unscrew the stripped one and screw the new part on. You just have to get it started unscrewing first ( remember that it's backwards! ).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from MIAMI BEACH, FL
- Parts Used:
- WPW10169511
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice would not dispense out of the ice bucket
SUPER EASY. I pulled out the ice bucket and confirmed the motor ran and the axel turned - however the coupling was missing. Ordered the coupling - pulled out the ice bucket, screwed on by hand with minimum effort, put ice bucket back and ice started coming out the door. It took less than 5 minutes and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SALINA, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
3 screws
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from MURFREESBORO, TN
- Parts Used:
- W11162443
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The crisper drawer has broken.
It was just a matter of pulling the old drawer out and sliding the née drawer in place. Ron was very helpful when ordering it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from WILLIAMSTON, NC
- Parts Used:
- W11188040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Added another shelf
Just slid it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Port Orchard, WA
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Changed the filter
Took the old one out and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from UNDERWOOD, MN
- Parts Used:
- W11371713
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holder broke along side towards the front
Slid weatherstripping off old and slid it on to new, replaced it into fridge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merrill from CHULA VISTA, CA
- Parts Used:
- W11162448
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic drawer
Pull out old drawer, push in new drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LITHIA, FL
- Parts Used:
- W11284458
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Not Working
Remove ice bin
Remove 3 screws
Disconnect wire harness
Remove ice maker
Install new ice maker
Connect wire harness
Install 3 screws
Put ice bin back in
Remove 3 screws
Disconnect wire harness
Remove ice maker
Install new ice maker
Connect wire harness
Install 3 screws
Put ice bin back in
Was this instruction helpful to you?
Thank you for voting!