WRS321SDHZ04 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from JACKSONVILLE, NC
- Parts Used:
- WP1119017
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice deflector had broken.
Removed ice tray and unbolted front cover. Removed broken piece and snapped new ice deflector in place. Reinstalled front cover and put ice tray back into freezer. Cycled crushed ice, works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Port Orchard, WA
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Changed the filter
Took the old one out and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
Drum and broken deflector
Remove the screws and detach the cover. loose the spring and unscrew backwards the plastic nut to release the drum. Un ensemble the blades and release the drum and the deflector replace new parts and ensemble again all the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from MIAMI BEACH, FL
- Parts Used:
- WPW10169511
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice would not dispense out of the ice bucket
SUPER EASY. I pulled out the ice bucket and confirmed the motor ran and the axel turned - however the coupling was missing. Ordered the coupling - pulled out the ice bucket, screwed on by hand with minimum effort, put ice bucket back and ice started coming out the door. It took less than 5 minutes and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerby from BEVERLEY HILLS, FL
- Parts Used:
- WPW10169511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice dispenser not working.
All I did was unscrew the stripped one and screw the new part on. You just have to get it started unscrewing first ( remember that it's backwards! ).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from MURFREESBORO, TN
- Parts Used:
- W11162443
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The crisper drawer has broken.
It was just a matter of pulling the old drawer out and sliding the née drawer in place. Ron was very helpful when ordering it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Goldsboro, NC
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice bin auger drum fins broke off from the main shaft,stopping the production of crushed ice.
Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merrill from CHULA VISTA, CA
- Parts Used:
- W11162448
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic drawer
Pull out old drawer, push in new drawer.
Was this instruction helpful to you?
Thank you for voting!