WRS315SDHT02 Whirlpool Refrigerator - Instructions

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Disassembled freezer icemaker rear panel and replaced defective part.

I remove the shelf above of the one that needing repair as well the one that required repair. I carefully place the white shelf frame into the rubber seals on the glass . Thirdly placed everything together.

Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..

Remove the screws and detach the cover. loose the spring and unscrew backwards the plastic nut to release the drum. Un ensemble the blades and release the drum and the deflector replace new parts and ensemble again all the parts.

Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.

Took the old one out and put the new one in

Just slid it in place

Very easy to install new handle. Used hex screw driver to remove screws at top and bottom of handle. Handle easily lifted off. Then installed new handle and tightened existing screws. No issues. Took 5 minutes. New handle fit perfectly and looks great.

I slid out the old drawer and slid in the new one. Easy peasy. Do make sure you get it properly in the grooves.

Three 1/4” nutdriver screws and a small plug in the rear of the icemaker. Installed in minutes, performed a reset. Working fine.

I removed the back cover that protected the motor and water inlet valve. Removed the screws that held the inlet valve to the refrigerator. Then I took a picture of the wiring and water lines on the inlet valve so I would make sure that I hooked up the new inlet valve properly. When I received the new inlet valve I removed the back cover which I had replaced and installed the new valve. It was a very easy process.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.